Atkore Flytec Floor Systems - Underfloor & Flush Floor Systems

Back to Blog Listing

Atkore Flytec Floor Systems - Underfloor & Flush Floor Systems

Flush Floor Shallow Screeds

Flush Floor Trunking body is supplied in 2 metre lengths complete with 2 x 1 metre lengths of lid secured by means of flush all steel turnbuckle fasteners. Each length of Flytec trunking is supplied with one external fitting connector.

Lids are manufactured from 3mm thick Galvanised steel. They are fully removable and may be flush or recessed by 3mm as standard. Other depths of recess can also be supplied.

It is advisable that all lid sections are fitted during screeding. This will prevent any slight inward movement to the sides of trunking body.

Atkore Unistrut recommend that Flush Floor Trunking is installed on a ribbon screed or similar to ensure support along the entire length and width of the system.

Service outlet boxes are available for shallow screed trunking.

• The underside of the box must be set lower into the floor to enable cables to pass under the socket outlet plates whilst maintaining lids to finish level with screed

• Carpet trim and lid assembly are manufactured in a tough plastic moulding which has two individual hinged cable outlets in dark grey

• The lid is reinforced by a 3mm steel plate.

• Carpet recess is 6mm

D6 Flush Floor Trunking Service Outlet Systems

Flytec’s flush floor trunking is supplied in 2 metre lengths, including 400mm lengths of removable lid which are interchangeable with a service outlet box, thus giving the designer flexibility of positioning within a screeded floor installation.

Flytec lids that are manufactured from 3mm thick Galvanised Steel are fixed to the trunking body by countersunk zinc plated steel turnbuckle fastners, providing speed of fitting by the installer and maximum rigidity of the finished product.

Key Features

• Available in two or three compartments

• It is advisable that all lid sections are fitted during screeding. This will prevent any slight inward movement to the sides of trunking body.

The Flush Floor Trunking is installed on a ribbon screed or similar to ensure support along the entire length and width of the system.

Two Compartment Service Box

• 2 compartment service box designed to fit into the trunking anywhere along the system layout excluding unction points

Three Compartment Service Box

• 3 compartment service box designed to fit into the trunking anywhere along the system layout excluding junction points 

• All sockets or variation of plates can be supplied on request

• Carpet trim & lid assembly manufactured in a tough plastic moulding containing two individual hinged cable outlets in dark grey

• The lid is reinforced by a 3mm steel plate and the carpet recess is 6mm

Underfloor Trunking

Underfloor Trunking is designed for placng on the constructional concrete slab, to be completely covered when the final floor screed is laid and the service outlet positions fixed.

• Steel Underfloor Trunking is manufactured in 2 metre lengths

• Two or three compartment are most commonly used

• Single or other numbers of compartments can also be supplied

• The trunking lengths are a total welded construction with no need to couple together loose channel sections

• Each length is joined together by a saddle clamp and plate, which prevent any ingress of screed into the duct


Underfloor Trunking Accessories

Junction boxes part numbers UF/JB (75mm deep as standard, other depths available)

• Junction boxes are supplied with flange couplers and blank plates to enable use as angles, tees or 4 way

• Each box is complete with Fly-Over for cable segregation

• Carpet recess is 6mm

• Please note: Junction boxes cannot be used to house sockets or data outlets

Chequer Plate Trunking

When a Flush Floor Trunking is required in an area where excessive loads will be transported such as a warehouse or industrial environment, Atkore Unistrut manufacture a robust steel trunking body fitted with a 6mm thick chequer plate lid fixed into place by M6 countersunk screws.

It is recommend that Flush Floor Trunking is installed on a ribbon screed or similar to ensure support along the entire length and width of the system.

It is advisable that all lid sections are fitted during screeding. This will prevent any slight inward movement to the sides of the trunking body.

Single or multi-compartment options are available with a range of accessories, including:

• Riser Bend

• Stop End

• Flat Bend

• Tee

• Crossover

*Service boxes are not available with chequer plate trunking

Service Outlet Boxes

For screed or raise floor applications 

Available in 2, 3 or 4 compartments

• Outer box with 20mm and 25 mm knockouts of two sides

• Standard box depth is 75mm, other sizes are available

• A wide range of outlet plates to carry voice, data and power sockets

• Available with a dark grey carpet trim fitted as standard or a stainless steel trim

• Deep lid recess boxes can be manufactured to accommodate stone, marble or timber infill

Contact our technical team on technical@dpbuildingsystems.co.uk for free advice and help on the best Atkore Flytec solution for your needs

For more information on Atkore Flytec products and services Click Here